Got questions about Concrobium Mold Control?
We’ve got answers. And if you don’t see your question here, please contact us.
EPA RegistrationWhy is EPA registration important for an antimicrobial product like Concrobium Mold Control?
Any product claiming to eliminate or prevent fungi or mold requires registration with the US Environmental Protection Agency. Registration is issued after review of efficacy data.
Yes, Concrobium Mold Control’s EPA registration number is 82552-1.
IngredientsI see Sodium Carbonate listed on the label. Is Concrobium Mold Control just Sodium Carbonate (washing soda) and water?
No. Sodium Carbonate is the listed “active ingredient” on the Concrobium Mold Control label, but in fact there are two other ingredients in the solution which, when combined with the sodium carbonate and the water, result in this patented tri-salt polymer that eliminates and prevents mold. (Sodium Carbonate and water alone are not effective against mold.) The solution contains no bleach, ammonia or VOCs. Our Material Safety Data Sheet is posted on our website.
BleachCan’t I just use bleach to get rid of the mold in my house?
Bleach can be toxic and poses health risks to users and to occupants during and after use.
Also, bleach will not prevent the mold from returning to the cleaned surface. It may look clean once you’re done, but the mold will grow back within weeks.
Bleach is particularly ineffective at treating mold on porous surfaces such as drywall, lumber and grout.
When bleach attacks surface mold, it leaves a carbon layer residue that prevents Concrobium Mold Control from penetrating to the mold roots or hyphae. This can limit the product’s effectiveness. If you’ve already treated a moldy area with bleach in the past, you should first wipe the area down with warm water and detergent to remove the layer. Once the area is dry, apply Concrobium Mold Control as recommended in the usage instructions.
Concrobium Mold Control is ready to use. Any added substance will act as a dilution and affect Concrobium Mold Control’s efficacy.
Safety PrecautionsDo I need to wear a mask when using Concrobium Mold Control?
Concrobium Mold Control does not contain any VOCs and does not off-gas. However, if you’re in an area with heavy mold growth, a mask would be a good idea to limit your inhalation of harmful mold spores. If fogging, it’s a good idea to avoid breathing in excessive moisture from the fog.
No. Concrobium contains no ammonia, acids, bleach or VOCs. Evacuation of the area during use is not required.
Yes. It leaves no residue that would be harmful to animals.
To access the Material Safety Data Sheet and other technical information for Concrobium Mold Control, please click here.
CoverageHow much Concrobium Mold Control do I need?
The product works as it dries, so the surface only needs to be lightly wetted for it to be effective. Avoid over-application as it can result in some white residue forming as the product dries. If you do get residue, just wipe it away with a Concrobium Mold Control -dampened cloth.
Surface coverage will depend on surface absorbency and application method. The more porous the surface (e.g., fabrics), the more product will be required. Raw construction materials like drywall, wood products and cinder blocks will be more absorbent than painted surfaces or smooth surfaces like vinyl or poured concrete. Fogging will give you the greatest coverage – 1/2 gallon will cover approximately 1,400 sq. ft. of surface area (the equivalent of all the walls, ceiling, and floor in a 20’ x 20’ room). If using a compression or garden sprayer, a fine mist nozzle should give you approximately 350-450 sq ft of surface coverage.
Using Concrobium Mold ControlCan I use Concrobium Mold Control in the kitchen?
Yes. Concrobium Mold Control contains no bleach, ammonia, alcohol or other harmful chemicals, making it appropriate for food-serving areas.
Yes. Concrobium Mold Control is an effective solution for eliminating and preventing mold in the shower. Repeated exposure to water may require more frequent applications to ensure microbial resistance.
Yes, it is! Concrobium Mold Control is non-toxic and is made up of water and food-grade, inorganic salts making it safe for septic systems.
Concrobium Mold Control was primarily designed to eliminate and prevent indoor mold. Two products for outdoor use that are non-toxic and bleach-free are Concrobium House & Deck Wash and Concrobium Mold Stain Eraser which are ideal for cleaning moldy exterior surfaces. These products are not registered antimicrobials. They do not eliminate or prevent mold growth.
Concrobium Mold Control bonds to the surface at a molecular level and is difficult to remove. However, if it has been applied to a surface that is continually exposed to water (e.g., leaking, washing, running water), you may need to reapply the product periodically to maintain protection against mold growth.
Concrobium Mold Control contains no bleach or whiteners. Once you have sprayed the solution on the moldy surface and allowed it to dry, the mold has been encapsulated and eliminated – in other words, your mold problem has been eradicated. If staining or residue remains, scrub with a Concrobium-dampened cloth or brush – or take other cosmetic steps to improve the look of the surface. Remember that once the cleaning step is complete it’s important to leave a layer of Concrobium Mold Control on the surface to provide mold resistance.
Depending on the area or surface you are treating with Concrobium Mold Control, you can apply the solution by: spray bottle (small targeted areas); brush or roller (trim); pump sprayer (large, accessible areas like walls); or cold fogger (large, enclosed areas like basement or attics).
Concrobium Mold Control needs to make direct contact with the moldy surface to be effective. If mold is suspected behind drywall you will need to remove the drywall to treat the area or create / find an opening into which Concrobium Mold Control can be sprayed or fogged. The solution will not penetrate a solid barrier.
Drying time depends on humidity levels and temperature in the area as well as the surface to which the solution was applied. Generally, it will dry in less than 2 hours. If you are painting on top of the Concrobium Mold Control application, you should allow 24 hours of drying time. If fogging, open windows to accelerate drying and to facilitate air exchange after fogging is complete.
Yes, Concrobium Mold Control can freeze in sub-zero temperatures. If it does freeze, the product can still be used after thawing and stirring or shaking it up.
Concrobium Mold Control does not expire.
We do not put any expiration dates for product sold in the US. In Canada, the printing of a specific expiration date is a regulatory requirement by Health Canada which is determined by manufacturer data. While we have chosen a 5-year period for marketing and merchandising reasons, in fact our testing data demonstrates that the product retains its Health Canada approved level of efficacy beyond the expiration window.
The optimal temperature to apply Concrobium Mold Control is 10°C or 50°F. Remember, if the product does not get the chance to dry then it won’t get the chance to work.
We’ve had customers report good success treating the front rubber ring and other parts of front-end loaders … give it a try! (But just make sure it dries before running the unit again – remember Concrobium Mold Control works as it dries.)
One application should be satisfactory as long as there is no water or humidity problem in the area. More frequent application may be required for shower and bathtub applications (ie. where the area is exposed to running water) or in areas where there is excessive humidity or condensation.
No, the product is ready-to-use and should not be diluted.
Yes, compression or garden sprayers (available at local home improvement retailers) are an excellent way to cover large surfaces that are easily accessible. It is important to use the nozzle that creates the finest mist. After spraying, wipe off excess wetness to ensure an even coating of the solution.
Yes. Regular household paints adhere very well to Concrobium Mold Control-treated surfaces. If you wish to treat and then repaint a moldy surface, first apply the solution to clean the affected area. Allow to dry and then repaint. To prevent regrowth, retreat the newly painted area with Concrobium Mold Control – ensuring first that the newly painted surface is dry.
Yes. To ensure that the mold on the surface does not grow through the paint or priming, you should first treat the moldy surface with Concrobium Mold Control. Once it has dried, you can then proceed with your painting project. Remember, it’s a good idea to treat the finished wall with more Concrobium Mold Control after the paint has fully cured, to ensure long-lasting protection of that area from future mold growth.
When Concrobium Mold Control dries on the moldy surface it encapsulates and crushes the cells right down to the root structure of the mold spores. This action is not visible, but you can be assured that it’s working. While you may be used to using bleach or bleach-based products that whiten the mold stain, this product contains no bleaches or whiteners so may require some mechanical action to remove the stain.
Concrobium Mold Control works as it dries. If the surface on which you’re applying the product is continuously wet, it may never get the chance to dry and may never therefore get a chance to work. Whatever the mold problem you’re having, you should always deal with the root cause of the water intrusion before using our product.
Concrobium Mold Control is odorless.
Yes, Concrobium Mold Control is safe to use around plants and greenery. Concrobium Mold Control does not require surrounding plants and grass be covered, however spraying directly onto plants is not recommended. If significant over spray makes contact with plants, you may wish to consider spraying or misting the plants with water.
SurfacesOn what surfaces can Concrobium Mold Control be used?
Concrobium Mold Control is EPA-registered for and effective on both hard and fabric surfaces, including wood, drywall, tile, stone, cement, masonry, fabric, upholstery and virtually any other household surface. If you’re uncertain, contact us or test on an inconspicuous section.
Yes, Concrobium Mold Control is effective on fabrics. It is EPA-registered for use on both hard and fabric surfaces.
Concrobium Mold Control is a very effective cleaner, though in some circumstances you may find that the mold stains left on a surface are embedded and very difficult to scrub away. In this case, ensure that the treated surface is completely dry so that the mold spores have been eliminated.
Next, address the cosmetic stain by, for example, painting a stained wall, or using a grout whitener on a mold-stained tile wall. Finally, to ensure that surface is protected against future mold growth, reapply Concrobium Mold Control and wipe the surface dry.
No, Concrobium Mold Control will not discolor hard or fabric surfaces, as there are no bleaching agents in the product. As with any cleaning solution, it’s always a good idea to test Concrobium Mold Control on an inconspicuous section first. NOTE: In our years of experience we’ve encountered just two surfaces that can have negative reactions to Concrobium Mold Control: suede and billiard balls. (We’re still not sure why someone would apply it to the latter!)
Yes. Food contact surfaces should be wiped down before use.
Concrobium Mold Control is great for eliminating odors in carpets since its encapsulating action traps and eliminates odor-causing particles. It will not discolor the carpet, though it’s still a good idea to test on an inconspicuous section first just to be sure. If you suspect mold in your carpet, you should pull it back to see if mold is growing on the subfloor and underpadding as well.
Because tile grout is porous, mold that has grown into it for some time may be very difficult to remove. Using Concrobium Mold Control in conjunction with a stiff bristle brush will get rid of most tile grout mold. However, if the mold has been there a long time, additional measures may be needed. First spray the area with Concrobium Mold Control to treat the mold. Then use a grout whitener to cover or remove the stain. Lastly, once dry and clean, use Concrobium Mold Control again to lay down the protective barrier.
It is best to allow surfaces to dry first before applying Concrobium Mold Control since excessive moisture or water on the surface can dilute the product and impact its efficacy.
Concrobium Mold Control should not harm paper or painted surfaces. However, common sense should be used if an item is of value. If fogging an area, it’s best to remove anything that you would not want to get wet. If unsure, test on an inconspicuous area first.
Concrobium Mold Control is effective in removing stains from most surfaces including caulking. Mold that has grown into the porous caulking surface may be difficult to remove, however. It may be more effective to strip out the old caulking, wipe the area down with Concrobium Mold Control and then re-caulk once the area is dry. You should then spray more Concrobium Mold Control on the caulk once it itself is dried. If you do not want to remove the caulking, spray the area with Concrobium Mold Control and allow to dry. Then treat any remaining stains with a whitening agent. Always follow up with more Concrobium Mold Control to provide the protective barrier against future mold growth.
FoggingWhen fogging Concrobium Mold Control, what contents should be removed from the room?
Prior to fogging Concrobium Mold Control, remove or cover any items you would not normally want to get damp, including paper, books and electrical equipment.
Residue is a normal result of overapplication of Concrobium Mold Control on non-absorbent surfaces. It is the result of evaporation of the water content from the solution as it sits pooled on a surface. The residue can be easily wiped away with a cloth dampened with Concrobium Mold Control. Adjust application rates accordingly for subsequent applications.
You need to use a cold fogger, one without a heating element (i.e., NOT a thermal fogger). You can use any type of electric applicator as long as there is no heat introduced and the product will not be diluted by water. If using an airless sprayer, ensure that the nozzle chosen does not create too fine a mist as the product may evaporate before reaching the surface.
MoldWhat is the difference between mold and mildew?
Technically mildew is the fungi that grow on plants. Most people refer to mold as a dry growth and mildew as a wet growth. Concrobium Mold Control is effective against both.
Concrobium Mold Control works on all types of fungi/mold. Its physical mode of action doesn’t differentiate between the type of mold.
Using Concrobium Moisture GrabbersAre Concrobium Moisture Grabbers safe to use around children and pets?
Concrobium Moisture Grabbers are self-contained pouches, therefore it is unlikely for the contents to spill or come in contact with children or pets. While the ingredients within the pouches do not contain harmful chemicals, it is best to keep pouches out of reach.
For most people, exposure to the contents should not pose any health effects or irritability. However, if contents come in contact with skin rinse thoroughly with water.
For those instances where it is impractical to use a traditional electric dehumidifier, Concrobium Moisture Grabbers were designed to be used in small, confined spaces (e.g. closets, bathrooms, cabinets, pantries, storage bin, safes, car and trucks, etc.).
Concrobium Moisture Grabbers will not dry out physical spots of water (i.e. water that has resulted from a flood or leak). Like any desiccant product Concrobium Moisture Grabbers will only absorb excess moisture from the air.